See what our Experts say about this CE Smith Boat Trailer Parts

• Recommended Keel Roller For Best Weight Capacity on Boat Trailer
  The Yates Keel Roller for Boat Trailers - Super-Heavy-Duty Rubber - 18" Long - 5/8" Shaft # YR18244-165EC is not weight rated. The weight of the boat will actually be on the bracket and the 5/8 inch shaft that runs through the heavy-duty roller. Your application with the front weight the roller is more likely to bend the longer you make the roller. For instance the 18 inch roller along with the brackets # CE10500G and Roller Shaft w/Cap Nuts 19" x 5/8" # 107-30A will be more likely...
  view full answer...
• How To Install Rollers On a Pontoon Boat
  It sounds like you are trying to bring the boat down closer to the trailer frame. I have personally not seen many setups that involve using keel rollers like the CE Smith Deep V Keel Roller Assembly part # CE10455G with a pontoon boat but if you have an idea in mind we do have these in various sizes. That said, I think the best option we can offer you to add a roller would be with the Dutton-Lainson Boat Trailer Deluxe Roller Bunks part # DL21741 and the CE Smith Bolster Bracket for Pontoon...
  view full answer...
  
• Keel Roller Solution for Tracker 14 Grizzly to Help Center Boat
  The CE Smith Deep V Keel Roller Assembly # CE10453G would work great to help center the boat as you load it onto the trailer as well as provide some additional support. I'd go with the wider version part # CE10455G which has a 12 inch roller on it. You'd need to provide your own U-bolts to fit around your frame channel to go through slots like what you see in the attached picture.
  view full answer...
  
• Will 12 inch Keel Roller Help Load Boat on Trailer in River
  Yes the CE SMith Deep V Keel Roller part # CE10455G that you referenced will help center your boat as you pull it up on the trailer. The 12 inch version would not be overkill. Using two of these like what you see in the picture I attached will do a great job keeping your boat centered as you load it. This will help with crosswinds and river currents like you are dealing with.
  view full answer...
  
• Do Boat Trailer Keel Rollers Need to Support Full Weight of Boat
  The bunks should be what's bearing the weight of the boat on the trailer and the rollers like the # CE32015G are designed to make enough contact that they guide the boat on the trailer but not fully support the boats weight. Think of them as supportive guides for the boat so that it sits properly. The # CE32015G is a great option for the front of the boat and then for at the rear a lower and flatter option like the part # CE10455G would be a better option.
  view full answer...
• Bow Roller Solution for Jon Boat that Has Flatter and Wider Bow
  Based on what you described you might be best served with a keel roller assembly like the # CE10455G which is 12 inches long and has a pretty low angle to the roller which sounds like would be a great match for the contour of the bottom of your boat.
  view full answer...
  
• Can the CE Smith Deep V Keel Roller Assembly Part # CE10455G Support a 9,000 Lb Boat
  The CE Smith Deep V Keel Roller Assembly part # CE10455G will do an excellent job of helping to guide the boat out of the water and position it onto the boat trailer all while reducing the stress on your winch. However, using just one of the rollers would not offer enough support for your 28' long 9,000 lb boat. In order to support the weight of the boat you will want to use several of the rollers positioned them just slightly above the frame rail so they are not taking responsibility for...
  view full answer...
  
• Replacement 11-3/8 Inch Long Keel Roller for a Boat Trailer
  With 12 inch keel rollers, such as # YR12244-125EC for example, they aren't actually 12 inches long. They fit 12 inch wide brackets. Just the rubber part of this roller for example is approximately 11-3/8 inches. Overall it is 11-3/4 inches long. So it is kind of like a 2 x 4 which is neither 2 inches nor 4 inches. The other option is to replace the roller and mounting bracket together using an assembly such as # CE10455G. I have linked videos of both of these parts for you.
  view full answer...
• Height of Keel Roller Assembly
  I believe you are just asking for the height of the CE Smith Deep V Keel Roller Assembly for Boat Trailers # CE10455G, and as you can see by the accompanying photo it is approximately 4 inches so you may be able to use it if that's the approximate height you are looking for. I have added a link to a video review of this assembly for you to check out as well.
  view full answer...
  
• How High Should the CE Smith Deep V Keel Roller Assembly # CE10455G be Installed
  It really just depends on your boat trailer setup. If you are using bunk boards as well then you would need the CE Smith Deep V Keel Roller Assembly # CE10455G to sit at a spot where it is sharing the load of the boat. If you will only be using the keel roller then I would place it just above the trailer as you can see a different customer did in the attached picture.
  view full answer...
  
• Replacement Boat Trailer Keel Roller and Bracket for 1996 Calkins Boat Trailer
  The linked page will show you all replacement keel rollers which are offered in both black rubber and non-marking thermoplastic varieties. You can use the filters on the page to narrow the results based on your preferred type and roller length, which ranges from 5- to 18-inches. The internal shaft diameter of all rollers we offer is either 5/8-inch or 1/2-inch so you'll want to check your existing bracket if it will be re-used. We also offer complete roller-with-bracket assemblies, shown...
  view full answer...
• Keel Roller Option that Can Fit with Transom Brace
  If you installed a keel roller that uses a U-bolt setup on the front of the trailer frame channel you could install the transom brace on the back side. Similar to the picture attached but on the last frame member which the roller in the picture is the # CE10455G.
  view full answer...
  
• CE Smith Deep V Keel Roller Assembly for a Ranger 620FS Boat Trailer
  Based on images I could find on your Ranger 620FS boat trailer they all use a wide keel roller like the 12" CE Smith Deep V Keel Roller Assembly # CE10455G. This particular roller is made of a thermal-plasticized rubber (TPR) which makes it stronger than rubber but will also not mar your boat keel. We do carry the CE Smith U-Bolts # CE15283GA-2 which will allow you to mount it on a 3" tall by 2" wide crossmember. If you have a different size crossmember let me know or you will be able...
  view full answer...
• Keel Roller Assembly Similar to a Roller Bunk
  Though we have roller bunks like # DL21741 and a Deep V Keel Roller Assemblies such as the 8" # CE10403G and 12" # CE10455G, we do not carry what would amount to a combination of the two. We also carry Keel Roller Assemblies that attach to either 2" trailer tongues # CE32005G or 3" trailer tongues # CE32003G. I've attached links to video reviews of these products for you to take a look at.
  view full answer...
• Distance from the Top of Roller to the Bottom of the Plate for the CE Smith Deep V Keel Roller
  I had this pulled and measured for you. The distance from the top of the widest point of the roller and the bottom of the mounting plate of the CE Smith Deep V Keel Roller Assembly for Boat Trailers, part # CE10455G, is 8-1/2". I've included a picture of this distance here and linked to a video review of it below.
  view full answer...
  
• Will CE Smith Deep V Keel Roller # CE10455G Prevent Front of Boat From Hitting Crossbeam on Trailer
  Yes, the CE Smith Deep V Keel Roller, # CE10455G, can be used on your trailer to prevent the front of the keel on your boat from hitting the cross beam. This roller will not only support your boat keel but will also help ease loading and unloading of the boat as well as absorb road shock while the boat is being trailered.
  view full answer...
• Replacement 12" Keel Roller Assembly for Boat Trailer
  Our current keel rollers are designed for a 12" Bracket # CE10305G. We do have these available with the 12" bracket as a Assembly # CE10455G so you get the new roller and shaft. This particular Roller # YR1200Y uses a thermal-plasticized rubber which is stronger than rubber and softer than polyurethane for durability without damaging or marring your boat.
  view full answer...
• Replacement Keel Roller Assemble For a Boat Trailer Using Rollers on 1-1/4" Shaft
  The only type of roller we have that fits a 1-1/4" shaft is the Yates Ribbed Wobble Roller # YA72FR. You can replace your rollers with the CE Smith Deep V Keel Roller Assembly # CE10455G. This 12" roller uses a 5/8" shaft and has a non-marking thermo-plastic rubber construction for increased life.
  view full answer...
• Hardware Requirements to Install CE Smith Deep V Keel Roller Assembly CE10455G
  The specific hardware to best install the CE Smith Deep V Keel Roller Assembly # CE10455G really depends on the desired mounting point on a particular trailer. U-bolts like # CE15283GA-2 are often a good option but other galvanized hardware you source locally may be better in some cases. Generally one pair of u-bolts would be sufficient for each roller in most typical installations.
  view full answer...

Do you have a question about this Boat Trailer Part?